iec inlet ? lters fn 9222e general performance iec inlet ? lter with earth line choke approvals rated currents up to 15a excellent performance/size ratio integrated earth line choke optional medical versions (b type) snap-in versions (s and s1 type) optional wide mounting flanges (cqc approval pending) typical applications the fn 9222e iec inlet filter combines an iec inlet and mains filter with excellent filter attenuation in a small form factor and integrated earth line choke. choosing the fn 9222e product line brings you the rapid availability of a standard filter associated with the necessary safety acceptances. standard iec connector filters are a practical solution helping you to pass emi system approval in a short time. a wide selection on amperage ratings, output connections, mounting possibilities and filters for medical appli- cations are designed to offer you the desired solution. exceptional conducted attenuation performance, based on chokes with high saturation resistance and excellent thermal behavior. rear/front or snap-in mounting. optional low leakage currents for medical applications. wide mounting flanges available. different output connections offering maximum flexibility for assembly. without earth line choke see fn 9222 data sheet. custom-specific versions are available on request. portable electrical and electronic equipment small to medium-sized machines and household equipment single-phase power supplies, switch-mode power supplies test and measurement equipment medical equipment rack mounting equipment features and benefits technical specifications maximum continuous operating voltage: 250vac, 50/60hz operating frequency: dc to 400hz rated currents: 1 to 15a @ 50c approvals by rated current: 1 to 10a (enec, cqc) 1 to 15a (ul, csa) high potential test voltage: p C> e 2000vac for 2 sec (standard types) p C> e 2500vac for 2 sec (b types) p C> n 1000vac for 2 sec protection category: ip40 according to iec 60529 temperature range (operation and storage): -25c to +85c (25/85/21) design corresponding to: ul 1283, csa 22.2 no. 8 1986, iec/en 60939 flammability corresponding to: ul 94v-2 or better mtbf @ 40c/230v (mil-hb-217f): 1,610,000 hours typical electrical schematic n e p line l2 cx r 2xl1 2xcy n e p load
> components > fn 9222e filter selection table fn 9222ex-1-06 1 (1.2) 373 12 0.4 0.1 2.2 -06 46 fn 9222ex-3-06 3 (3.5) 373 2.5 0.4 0.1 2.2 -06 46 fn 9222ex-6-06 6 (7.2) 373 0.78 0.4 0.1 2.2 -06 46 fn 9222ex-8-06 8 (10.6) 373 0.5 0.4 0.1 2.2 -06 46 fn 9222ex-10-06 10 (11.6) 373 0.225 0.1 0.1 2.2 -06 46 fn 9222ex-12-06 12 (12) 373 0.11 0.1 0.1 2.2 -06 46 fn 9222ex-15-06 15 (15) 373 0.075 0.1 0.1 2.2 -06 46 fn 9222ex-12-06hi 12 (12) 373 0.11 0.1 0.1 2.2 -06 46 fn 9222ex-15-06hi 15 (15) 373 0.075 0.1 0.1 2.2 -06 46 fn 9222exr-1-06 1 (1.2) 373 12 0.4 0.1 2.2 1000 -06 46 fn 9222exr-3-06 3 (3.5) 373 2.5 0.4 0.1 2.2 1000 -06 46 fn 9222exr-6-06 6 (7.2) 373 0.78 0.4 0.1 2.2 1000 -06 46 fn 9222exr-8-06 8 (10.6) 373 0.5 0.4 0.1 2.2 1000 -06 46 fn 9222exr-10-06 10 (11.6) 373 0.225 0.1 0.1 2.2 1000 -06 46 fn 9222exr-12-06 12 (12) 373 0.11 0.1 0.1 2.2 1000 -06 46 fn 9222exr-15-06 15 (15) 373 0.075 0.1 0.1 2.2 1000 -06 46 fn 9222exr-12-06hi 12 (12) 373 0.11 0.1 0.1 2.2 1000 -06 46 fn 9222exr-15-06hi 15 (15) 373 0.075 0.1 0.1 2.2 1000 -06 46 fn 9222exb-1-06 1 (1.2) 2 12 0.4 0.1 1000 -06 46 fn 9222exb-3-06 3 (3.5) 2 2.5 0.4 0.1 1000 -06 46 fn 9222exb-6-06 6 (7.2) 2 0.78 0.4 0.1 1000 -06 46 fn 9222exb-8-06 8 (10.6) 2 0.5 0.4 0.1 1000 -06 46 fn 9222exb-10-06 10 (11.6) 2 0.225 0.1 0.1 1000 -06 46 fn 9222exb-12-06 12 (12) 2 0.11 0.1 0.1 1000 -06 46 fn 9222exb-15-06 15 (15) 2 0.075 0.1 0.1 1000 -06 46 fn 9222exb-12-06hi 12 (12) 2 0.11 0.1 0.1 1000 -06 46 fn 9222exb-15-06hi 15 (15) 2 0.075 0.1 0.1 1000 -06 46 * maximum leakage under normal operating conditions. note: if the neutral line is interrupted, worst case leakage could reach t wice this level. filter rated current leakage current* inductance capacitance resistance output connections weight @ 50c (25c) @ 250vac/50hz l1 l2 cx cy r [a] [a] [mh] [mh] [f] [nf] [k] [g] product selector fn 9222exx-yy-..hi-zz snap-in range for s version only blank: snap-in range 0.7 to 1.5mm 20: snap-in range 1.5 to 2.2mm blank: standard iec inlet type c14 hi: hot iec inlet type c16 (12 and 15a types only) 06: faston 6.3 x 0.8mm (spade/soldering) 1 to 15: rated current blank: standard version r: bleed resistor b: medical version (with bleed resistor and without y2-capacitor) blank: standard housing with mounting ? anges u: housing with wider mounting ? anges s: snap-in version, snapper on vertical side s1: snap-in version, snapper on horizontal side for example: fn 9222e-15-06, fn 9222es1b-10-06-20, fn 9222er-12-06hi, fn 9222eub-8-06-20
> components > fn 9222e per cispr 17; a = 50/50 sym; b = 50/50 asym; c = 0.1/100 sym; d = 100/0.1 sym typical filter attenuation 1 and 3a types 6 to 10a types 12 and 15a types mechanical data fn 9222e fn 9222e-hi fn 9222es fn 9222es1 a c b e g s f d i 6.3 x 0.8 j a b e g fd i j 6.3 x 0.8 6.3 x 0.8 j i d f b a g e panel cut out installation t h h c s a b e g f d i j 6.3 x 0.8 fn 9222eu a c b e g s f d i 6.3 x 0.8 j h c p r m n
> components > fn 9222e your local partner: to find your local partner within schaffners global network, please go to www.schaffner.com may 2008 * for selecting the panel thickness, please refer to the filter selector table. all dimensions in mm; 1 inch = 25.4mm tolerances according: iso 2768-m / en 22768-m fn 9222e fn 9222eu fn 9222es fn 9222es1 fn 9222e-hi dimensions a 48 53 29.9 29.9 48 b 22.5 30 22.4 22.4 22.5 c 40 0.2 40 0.2 40 0.2 d 46.8 46.8 46.8 46.8 46.8 e 27.8 27.8 27.8 27.8 27.8 f 5.5 5.5 5.5 5.5 5.5 g 20.1 20.1 20.1 20.1 20.1 h ?3.3 ?3.3 ?3.3 i 14 14 14 14 14 j 13.3 13.3 13.3 13.3 13.3 m r 3 r 3 r 1.5 r 1.5 r 3 n 21.5 21.5 20.8 21.9 21.5 p 28.5 28.5 29.4 28.5 28.5 r m3 m3 m3 s 90 90 90 t* 0.7 - 1.5 0.7 - 1.5 t* 1.5 - 2.2 1.5 - 2.2
|
